Lrack dragonflies from plasticine

Lrack dragonflies from plasticine

Dragonflies of plasticine can be very fascinating. It is necessary to know not only how to make it out of natural materials, but also how to make the volumetric strip dragonfly.

Separate important topic – insect modeling on cardboard step by step.

How to make a simple cardboard?

Piercing over the heads of “helicopters” immediately pay attention to the warm weather. The beauty of this insect determines its popularity. For children, even urban, dragonflies are familiar not bad. Therefore reproduce them by modeling can be pretty fast. Blue material will be needed to create:

  • Corps+

  • Tail+

  • Head.

Orange plasticine is useful for the modeling of the wings. Everything is done step by step like this:

  • form 3 approximately similar to the dimensions of the ball (they are cut and kneaded with their hands)+

  • from one small ball walked head+

  • stretch the rest of the balls, roll them with your fingers+

  • give the body an oval configuration, but it still should be wider than the tail+

  • lengthen and thin the tail+

  • Connect all 3 cooked parts one after another+

  • We are finalized by stack+

  • draw it with the edge of the cross-type rings+

  • Add wings and eyes from large semi-grayscake green+

  • shift a figurine on the cardboard (if it was not subsected immediately).

How to blind volumetric dragonfly?

Giving the composition of the required volume is logically combined using bright and catchy material. In this case, the housing and tail make relatively dark color. Wings are pushed from plasticine brighter shades. Without difficulty you can form an elegant marble effect. It is necessary to work in stages like this:

  • Pull the ball to the state of “sausage”+

  • sharpen it from one face+
  • Cut with a stack, getting a split effect+
  • Apply notches in the longitudinal plane+
  • cut a separate piece on 4 fragments and stretch them into flat wings+
  • Fasten them on the hull, seeking the feeling of “fucking”+
  • hurry the wings straight regular notch+

  • Attach your head+

  • add to her eyes+

  • attach the rope if they want the plasticine dragonfly to flush as his prototype.

Crafts with natural materials

This option is actually different from previous few. It is difficult to say which color is useful when cutting dragonfly. Each of them is unique, and the types are different. The wings of the real insect are transparent, and denoted it is the easiest white color. Figures with leaves on the background of the dragonfly themselves look only in nature and more reliable.

Start work, rolling plasticine tiles in oval. The other part is pulled out like sausage. It will be a case and tail. As in the previous case, you need to take the stack and cutting them the edge of the tail. Mandital feature will also be longitudinal notches at all its length.

Next you need:

  • Drain the head ball to the body+
  • Stop big spherical eyes on the head+
  • form from white or beige plasticine 4 oblong wings+
  • attach these wings to the body of the insect+
  • Stip the wings of the confused ornament (but it is better to do it before mounting on the designated place)+
  • As needed to strengthen the wings with matches or wire+
  • Add the composition with leaves and twigs that are attached to the same cardboard.

But you can do and otherwise – to make a figure of dragonfly in which plasticine will play only auxiliary role.

From it pose belly and head. Seeds of any plants go to the manufacture of eyes. For the manufacture of tail used twig. To get wings, apply maple clips, and the paws and mustaches form from fine stainless or copper wire.

On how to make a dragonfly of plasticine, look in the video.

Rate the article
( No ratings yet )
Add comments

;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: