All about grinding of the lads

All about grinding of the lads

Landing strings on the guitar are the difficulty that will upset anyone with hearing. And it may occur even on a recently purchased tool. Eliminate this problem will help grinding. And it is worth considering how to fulfill this procedure yourself.

When guitar freedoms need grinding?

The causes of the phenomenon are in several factors. First, from the production of budget models, the final grinding is often excluded. Without attracting specialists, it is possible to reduce the cost of the instrument, but in fact the savings are done on the sound quality.

Secondly, if the regions of production and sales of the guitar do not coincide, the tool is undergoing climatic exposure. Due to the temperature and humidity drops, the tree begins to dying, drink moisture. As a result, the radius and height of the lads are changing.

Sometimes there is a human factor, including non-accuracy during transportation, the use of a kit with a smaller caliber when changing strings. The uniformity of the location of the lands is also lost when wear.

What do you need?

Before work, you will need to evaluate the tool condition. If the deviations from the norm are small, it makes sense in grinding. If there is a significant amplitude of the walking of the lands in the propils, they will have to loliden in order to achieve the desired fixation. At the same time, experienced masters recommend their full replacement. Considering that in cheap guitars, the Lada is performed from soft alloys, this procedure is inevitable.

For grinding and polishing the instrument will be required:

  • Malyan Scotch+
  • ruler+
  • marker+
  • bar+
  • Foods+
  • a hammer+
  • fellow+
  • sandpaper (1000, 1500, 2000)+
  • polishing circle.

For grinding also use steel wool, grinding hide on a tissue basis. You can polish them after alignment and rounding.

Technology

Grinding of the lands on an acoustic guitar is made according to a specific algorithm.

  1. First, you will need to remove the strings and make a painting tire with a painting.
  2. Then remove the deflection of anchor. On a flat hafe, evaluate the unity of the height of the lands will be easier.
  3. Now there is a long thick metal ruler. It should be put on the frets and check its position. Ideally, the device will fall smoothly and reliable. If the ruler formed a deflection, it means one of the elements below the rest. And the outstretched way will lead to the fact that the ruler will be swayed on it.
  4. Then the frets are painted with a marker. At this stage, they have to polish perfectly smooth bars and emery paper. It is important to maintain the uniformity of the press, moving from one edge of the Lada to another.
  5. After the passage of the passes it is worth estimating the status of the marker markup. If color traces remained, it means that these areas turned out to be below the level of grinding. Then it is necessary to re-apply the marker to the surface and run it so that the painted areas does not remain.
  6. Performing adjustment, you need to take into account some nuances. So, the first way may be slightly higher than the rest. And starting from the 12th, height is permissible to drop a bit.
  7. When the lads are found, getting out of the groove, it is worth using the hammer and a storage.
  8. After grinding, the threshings become flat. If they immediately stretch the strings, then because of the larger area of ​​contact, they will vibrate worse. So now the edges of the profile need to round up.
  9. Now you should take care of the return of the lads of the former smoothness and gloss. This requires 3 passages of sandpaper. The first time you need grain 1000, then – 1500, and in conclusion – 2000.
  10. Polishing will be the final stroke. For the procedure you need a special circle. Alternatively, the use of paste gay and soft vehicle is allowed. These funds are to graze to the brilliance every way. In this case, items should not overheat. Otherwise, they will shift again with grooves.

Now you can wear strings, rebuild their height, the position of the grid and evaluate the result of the work. Grinding is well done if the strings began to clamp easier, chords sound without dissonant impurities, when tightening there is a better slide string in Ladam.

Useful advice

      1. Before proceeding with grinding, it is worth sure that it is the cause of the ringing and pride. Sometimes the problem is to curvathes the griff, and it has to be solved otherwise.
      2. In case of inspection, it is important to take into account the height of the thresholds. If they are too low for sharpe, it is better to replace them.
      3. Do not overestimate your own strength. So, if we are talking about the restoration of an expensive guitar, and not about bringing into the order of the budget counterpart, it is better to trust a specialist. Otherwise, an attempt to save will turn large cash costs.

      Let’s summarize. The irregularities of the wards of height negatively affects the quality of the sound, which reduces the pleasure of the game. With this difficulty there are musicians who bought the tool recently and the owners of old guitars. When the irregularities are detected, their grinding and polishing are required. At least work and can be entrusted to the master, it is not difficult to level the frets on an acoustic, bass guitar or electric guitar with your own hands, observing simple instructions.

      About grinding of lads guitar See in the video.

      Rate the article
      ( No ratings yet )
      Add comments

      ;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: